New Holland E26C Operator'S Manual Download | Manualshive

Page: 177 / 282

background image

6 - MAINTENANCE

Battery

WARNING

Improper operation or service of this machine can result in an accident.
Before working on any component(s) of the electrical circuit, put the ignition key in the off (shut down)
position. When disconnecting batteries, always disconnect the negative (-) cable first. When recon-
necting batteries, always connect the negative (-) cable last.
Failure to comply could result in death or serious injury.

W0943A

WARNING

Battery acid causes burns. Batteries contain sulfuric acid.
Avoid contact with skin, eyes or clothing. Antidote (external): Flush with water. Antidote (eyes): flush
with water for 15 minutes and seek medical attention immediately. Antidote (internal): Drink large
quantities of water or milk. Do not induce vomiting. Seek medical attention immediately.
Failure to comply could result in death or serious injury.

W0111A

WARNING

Battery gas can explode!
To prevent an explosion: 1. Always disconnect the negative (-) battery cable first. 2. Always connect
the negative (-) battery cable last. 3. Do not short circuit the battery posts with metal objects. 4. Do
not weld, grind, or smoke near a battery.
Failure to comply could result in death or serious injury.

W0011A

WARNING

Explosive gas!
Batteries emit explosive hydrogen gas and other fumes while charging. Ventilate the charging area.
Keep the battery away from sparks, open flames, and other ignition sources. Never charge a frozen
battery.
Failure to comply could result in death or serious injury.

W0005A

Check the battery voltage every

250 h

.

Access to the battery

To access the battery proceed as follow:

1. Set the battery disconnect switch to O position (OFF

position) to cut off any power supply in the electrical
system of the machine (refer to

3-47

).

2. Remove the caps and the three bolts

(1)

.

3. Remove the left-hand side panel

(2)

.

SMIL17MEX2385AB

1

6-35

«
...
175
176
177
178
179
...
»

Summary of Contents for E26C



























































































































































































































































































Reviews:

No comments

Related manuals for E26C

Brand: Wacker Neuson Pages: 188

Brand: jcb Pages: 24

Brand: RHINOCEROS Pages: 52

Brand: RHINOCEROS Pages: 78

Brand: Menzi Muck Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands