background image

Check Box for These Contents 

In the event of missing or defective parts please call our customer service dept. at 

1 800 282 9346

(Mon. to Fri.8:00 AM to 4:00 PM EST)

 or UK Tel:

(44) 2038 687160

 - 

(Mon. to Fri. 1:00 PM to 10:00 PM GMT

).

 

Tools You Will Need

Tape Measure

Level

Sledge Hammer

Cordless Drill with #2 Phillips Bit

 

Purchased Separately

• Lam

p Fixture

General Information

Read Instructions through carefully before beginning assembly.

 When handling components, place on a non-abrasive surface

(i.e. shipping box) 

to avoid scratching. 

 We recommend an area approx 10’x 8’ (3m x 2.4m) for unobstructed handling.

Important Note:

Please refer to local codes before installing outdoor lighting. UF-rated cable should be used for underground

wiring and all materials should be approved by the Underwriter’s Laborator (UL). New England Arbors
assumes no liability for errors, ommissionsm or the outcome of any project.

4x4 Lamp Post with EZ Mount

Please read through before starting assembly.

ASSEMBLY  INSTRUCTIONS

1

Ver 1.

2-

01

22

18

3

Not to Scale

1

2

4

www.newenglandarbors.com

www.newenglandarbors.co.uk

73 7/8 in

(188 cm)

24 in

(61 cm)

24 in

(61 cm)

3 in (7.6 cm)

Diameter

1. Lamp Post (1)

 -  4” x 4” x 72” (10x10x183cm) - 10273 

2. EZ Mount Anchor Assembly (1)

 -  1 5/8“ Diameter x 48” (4cm Diameter  x  122cm) - 11102

3. Post Cap (1)

 - 10272

4. 5/8“ (16mm) Self-Tapping Screw (1)

 -   20016 

5. Tube of Vinyl Weld (1)

 -   20000

5

Summary of Contents for VA94436






Reviews: