background image

Spate cleaner TANKO-SF 

 

 

1 Introduction 

Translation of the original Operating / Installation Instructions 2016/09 Rev.1  1/63  

 

 

1

 

Introduction 

These operating/installation instructions (referred to hereinafter as the instructions) are a component 
part of the device. They provide you with all the information required for smooth operation of the 
TANKO

®

SF spate cleaner (referred to hereinafter as the device). 

The instructions must be read, understood, and applied by all persons employed to carry out installation 
and assembly, maintenance, cleaning and troubleshooting on the device. This applies in particular to 
the listed safety notes. 

After studying the instructions, you will be able to 

– 

assemble, install and operate the device safely, 

– 

clean and service the device correctly and 

– 

take the correct measures if a fault occurs. 

In addition to these instructions, generally valid, statutory and other binding regulations in regard of the 
prevention of accidents and in regard of environmental protection in the country of use must also be 
observed. 

The instructions must be kept at the location of use of the device so that it is available in legible condition 
at all times. If the device is resold, the instructions must always be transferred to the new owner. 

Download the instructions if necessary from th

http://www.awh.eu/de/downloads

 Internet page. 

1.1

 

Means of Presentation 

1.1.1

 

Explanation of Signal Words 

The warnings are introduced with a signal word which describes the extent of the hazard. The meaning 
and their classification in case of hazardous situations are explained in the following overview. 

Signal Word 

Meaning 

Consequences of Failure to Observe 

 DANGER 

Hazard 
with a high level of risk  

Death or severe physical injuries 

 WARNING 

Hazard 
with a medium level of risk 

Death or severe physical injuries 

 CAUTION 

Hazard 
with a low level of risk 

Minor or moderate physical injuries 

NOTE 

Hazard 
with a low risk 

Risk of material damage 

Table 1.1-1: Overview of Signal Words 

 

Summary of Contents for AWH TANKO SF40









































































Reviews: