Netstor NS780TB3 User Manual Download Page 11 | Manualshive

Page: 11 / 21

background image

11

2. Power on the Thunderbolt 3 host computer, and then the NS780TB3 storage will

be powered on along automatically.

6. Power On/Off

NS780TB3 is designed to be powered on/off by the Thunderbolt 3 host computer.

1. Connect one end of power cord to the power cord receptacle at rear of NS780TB3

enclosure, and the other end of power cord to the power outlet.

1.

2.

«
...
9
10
11
12
13
...
»

Summary of Contents for NS780TB3






















Reviews:

No comments

Related manuals for NS780TB3

EPIC By-Pass Sliding Doors

Brand: GlassCrafters Pages: 13

Brand: Rosewill Pages: 12

Brand: Gigaware Pages: 2

Brand: Aerocool Pages: 2

Brand: Adicos Pages: 28

Brand: Gigabyte Pages: 1

Brand: TOOQ Pages: 22

Brand: Phanteks Pages: 26

Brand: Phanteks Pages: 38

Brand: Velkase Pages: 17

FUSION D800RAID

Brand: Sonnet Pages: 6

Brand: Icy Box Pages: 10

Brand: Icy Box Pages: 16

Brand: Icy Box Pages: 23

Brand: DCS Pages: 2

U357-1M2-NVMEG2

Brand: Tripp Lite Pages: 72

Brand: DAS Pages: 32

Brand: i-tec Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands