NETGEAR R6400v2 User Manual Download Page 10

Page: 10 / 178

Hardware Setup

AC1750

Smart WiFi Router

Top and Front Panels

The router includes status LEDs on top and a USB 3.0-Storage port on the front.

USB 3.0-Storage port

Figure 2. Router top and front view

Table 1. LED and button descriptions

LED

Description

Power

•

Solid amber

. The router is starting.

•

Blinking amber

. The firmware is upgrading, or the

Reset

button was pressed.

•

Solid white

. The router is ready.

•

Blinking white

. The firmware is corrupted.

•

Off

. Power is not supplied to the router.

Internet

•

Solid white

. The Internet connection is ready.

•

Solid amber

. The router detected an Ethernet cable connection to the modem.

•

Off

. No Ethernet cable is connected between the router and the modem.

2.4 GHz WiFi

•

Solid white

. The 2.4 GHz WiFi radio is operating.

•

Blinking

. The router is sending or receiving WiFi traffic.

•

Off

. The 2.4 GHz WiFi radio is off.

5 GHz WiFi

•

Solid white

. The 5 GHz WiFi radio is operating.

•

Blinking

. The router is sending or receiving WiFi traffic.

•

Off

. The 5 GHz WiFi radio is off.

USB
3.0-Storage
port)

•

Solid white

. A USB device is connected and is ready.

•

Blinking

. A USB device is plugged in and is trying to connect.

•

Off

. No USB device is connected, or someone clicked the

Safely Remove Hardware

button, and it is now safe to remove the attached USB device.

Summary of Contents for R6400v2



















































































































































































Search results

Summary of Contents for R6400v2

Reviews:

Related manuals for R6400v2

Brands by name

Popular brands

NETGEAR R6400v2, User Manual

Search results

Summary of Contents for R6400v2

Reviews:

Related manuals for R6400v2

Brands by name

Popular brands