manualshive.com logo in svg

NETGEAR ProSafe GSM7324, Reference Manual, Page: 201 / 263

Share
Download
NETGEAR ProSafe GSM7324 Reference Manual Download Page 201

7000 Series L3 Managed Switch Reference Manual for Software v1.0

CLI Commands: Differentiated Services

9-35

May 30, 2003 Beta Draft

OperStatus  

The current operational status of this DiffServ service interface.

Policy Name  

The name of the policy attached to the interface in the indicated 
direction.

show diffserv service stats detailed

This command displays policy-oriented statistics information for the specified interface and 
direction. The 

<slot.port>

 parameter specifies a valid slot number and port number for the 

system. The direction parameter indicates the interface direction of interest.

Note: This command is only allowed while the DiffServ administrative mode is enabled.

Format  

show diffserv service stats detailed <slot.port> [in/
out]

  
Interface  

The slot number and port number of the interface (slot.port).

Direction  

The traffic direction of this interface service, either in or out. If 
the [in/out] optional parameter is not specified, statistics are 
shown for both directions (if available).

Operational Status  

The current operational status of this DiffServ service interface.

Policy Name  

The name of the policy attached to the interface in the indicated 
direction.

Interface Offered Octets/Packets   

A cumulative count of the octets/packets offered to this ser-

vice interface in the specified direction before the defined Diff-
Serv treatment is applied.

Interface Discarded Octets/Packets  

A cumulative count of the octets/packets discarded by this 

service interface in the specified direction for any reason due to 
DiffServ treatment.

Interface Sent Octets/Packets  

A cumulative count of the octets/packets forwarded by this ser-

vice interface in the specified direction after the defined DiffServ 
treatment was applied. In this case, forwarding means the traffic 
stream was passed to the next functional element in the data path, 
such as the switching or routing function or an outbound link 
transmission element.

The following information is repeated for each class instance within this policy:  Class Name  

The name of this class instance.

Summary of Contents for ProSafe GSM7324








































































































































































































































































Reviews:

No comments