NETGEAR Orbi RBRE950 User Manual Download Page 44 | Manualshive

Page: 44 / 160

background image

This setting specifies how the router assigns IPv6 addresses to the devices on your
home network.

8. (Optional) Select the Enable RIPng check box.

This selection enables RIP Next Generation (RIPng) on IPv6 Internet connections.
RIPng is an extension of Routing Information Protocol (RIP) that supports IPv6.

9. (Optional) Select the Use This Interface ID check box and specify the interface ID

that you want to be used for the IPv6 address of the router’s LAN interface.
If you do not specify an ID here, the router generates one automatically from its MAC
address.

10. (Optional) To set a specific MTU size for an IPv6 6rd tunnel Internet connection,

specify the MTU size in the MTU Size (in bytes) field.

11. Click the Apply button.

Your settings are saved.

Change the MTU size

The maximum transmission unit (MTU) is the largest data packet a network device
transmits. When one network device communicates across the Internet with another,
the data packets travel through many devices along the way. If a device in the data path
uses a lower MTU setting than the other devices, the data packets must be split or
“fragmented” to accommodate the device with the smallest MTU.

The best MTU setting for NETGEAR equipment is often the default value. In some
situations, changing the value fixes one problem but causes another. Leave the MTU
unchanged unless one of these situations occurs:

•

You experience problems connecting to your ISP or other Internet service, and the
technical support of either the ISP or NETGEAR recommends changing the MTU
setting.
For example, if a secure website does not open, or displays only part of a web page,
you might need to change the MTU.

•

You use VPN and experience severe performance problems.

•

You used a program to optimize MTU for performance reasons, and now you are
experiencing connectivity or performance problems.

Note: An incorrect MTU setting can cause Internet communication problems. For
example, you might not be able to access certain websites, frames within websites,
secure login pages, or FTP or POP servers.

User Manual

44

Specify Your Internet Settings

Orbi Quad-Band Mesh WiFi 6E System

«
...
42
43
44
45
46
...
»

Summary of Contents for Orbi RBRE950

































































































































































Reviews:

No comments

Related manuals for Orbi RBRE950

Brand: D-Link Pages: 29

DGS-3700 Series

Brand: D-Link Pages: 292

Brand: D-Link Pages: 140

DGS-1224T - Web Smart Switch

Brand: D-Link Pages: 61

DI-LB604 - Load Balancing Router

Brand: D-Link Pages: 14

Brand: D-Link Pages: 2

Brand: D-Link Pages: 45

Brand: D-Link Pages: 218

DES-3528 - xStack Switch - Stackable

Brand: D-Link Pages: 322

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 10

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 4

DIR-130 - Broadband VPN Router

Brand: D-Link Pages: 13

Brand: D-Link Pages: 13

DI-804HV - Express ENwork Router

Brand: D-Link Pages: 19

Brand: D-Link Pages: 12

Brand: D-Link Pages: 8

Brand: D-Link Pages: 16

Brand: D-Link Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands