NETGEAR Nighthawk CAX30 User Manual Download Page 14

Page: 14 / 140

•

Place the modem router away from electrical devices such as these:

Ceiling fans

Home security systems

Microwaves

Computers

Base of a cordless phone

2.4 GHz cordless phone

•

Place the modem router away from large metal surfaces, large glass surfaces, and
insulated walls, and items such as these:

Solid metal doors

Aluminum studs

Fish tanks

Mirrors

Brick

Concrete

Install and Activate Your Modem Router

The modem router provides a connection between your cable Internet provider’s
network and your computer, router, or WiFi router.

Connect Your Modem Router to a Computer

During the installation and activation, you must connect the modem router directly to
a computer.

User Manual

Hardware Setup

Nighthawk AX6 AX2700 WiFI Cable Modem Router Model CAX30

Summary of Contents for Nighthawk CAX30













































































































































Search results

Summary of Contents for Nighthawk CAX30

Reviews:

Related manuals for Nighthawk CAX30

Brands by name

Popular brands

NETGEAR Nighthawk CAX30, User Manual

Search results

Summary of Contents for Nighthawk CAX30

Reviews:

Related manuals for Nighthawk CAX30

Brands by name

Popular brands