NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 98 / 162

Display the statistics of the Internet port

To display the statistics of the Internet port:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Click the ADVANCED tab.

The ADVANCED Home page displays.

5. In the Internet Port pane, click the Show Statistics button.

The Show Statistics window opens and displays following information:

•

System Up Time. The time elapsed since the router was last restarted.

•

Port. The statistics for the WAN (Internet) port, LAN (Ethernet) ports, and WLANs.
For each port, the window displays the following information:

Status. The link status of the port.

TxPkts. The number of packets transmitted on this port since the router was
last started.

RxPkts. The number of packets received on this port since the router was last
started.

Collisions. The number of collisions on this port since the router was last
started.

Tx B/s. The current transmission (outbound) bandwidth used on the WAN
and LAN ports.

Rx B/s. The current reception (inbound) bandwidth used on the WAN and
LAN ports.

Up Time. The time elapsed since this port acquired the link.

Poll Interval. The interval at which the statistics are updated on this page.

User Manual

Manage Your Router

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands