NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 126 / 162

To change your settings:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > Advanced Setup > Dynamic DNS.

The Dynamic DNS page displays.

5. Change your DDNS account settings as necessary.

6. Click the Apply button.

Your settings are saved.

Access USB storage devices through the
Internet

You can access USB storage devices through the Internet when you’re not home.

To access devices from a remote computer:

1. Launch a web browser on a computer that is not on your home network.

2. Connect to your home router:

• To connect with Dynamic DNS, type the DNS name.

To use a Dynamic DNS account, you must enter the account information on the
Dynamic DNS page. See Set up and manage Dynamic DNS on page 122.

• To connect without Dynamic DNS, type the router’s Internet port IP address.

You can view the router’s Internet IP address on the BASIC Home page.

You can use FTP to share files on a USB device connected to the router.

User Manual

126

Use Dynamic DNS to Access USB
Storage Devices Through the
Internet

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands