NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 12 / 162

Rear panel

The following figure shows the rear panel connectors and buttons.

Figure 3. Rear panel

The rear panel contains the following components:

1. Reset button. Pressing the Reset button resets the router.

If the Reset button is pressed for at least 10 seconds and the Power LED blinks, the
router returns to its factory settings.

2. USB 3.0 port. Use the USB 3.0 port to connect USB storage device.

3. Ethernet ports. Four Gigabit Ethernet RJ-45 LAN ports. Use these ports to connect

LAN devices to the router.

4. Internet port. One Gigabit Ethernet RJ-45 WAN port to connect the router to an

Internet modem such as a cable modem or DLS modem.

5. DC power connector. Connect the power adapter that came in the product package

to the DC power connector.

6. Power On/Off button. Press the Power On/Off button to provide power to the

router.

User Manual

Hardware Setup

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands