NETGEAR Nighthawk AX6 AX4300 User Manual Download

Page: 116 / 162

6. Click the Connect button.

A window automatically opens and displays the files and folders on the USB storage
device.

Enable FTP access within your network

File Transfer Protocol (FTP) lets you download (receive) and upload (send) large files
faster.

To enable FTP access within your network:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

The user name is admin. The password is the one that you specified the first time
that you logged in. The user name and password are case-sensitive.

The BASIC Home page displays.

4. Select ADVANCED > USB Functions > ReadySHARE Storage.

The USB Storage (Advanced Settings) page displays.

5. Select the FTP check box.

6. Click the Apply button.

Your settings are saved.

View network folders on a storage device

You can view network folders on a storage device that is connected to the router.

To view network folders:

1. Launch a web browser from a computer or mobile device that is connected to the

router network.

2. Enter http://www.routerlogin.net.

A login window opens.

3. Enter the router admin user name and password.

User Manual

116

Share USB Storage Devices
Attached to the Router

Nighthawk AX6 6-Stream AX5400 WiFi Router

Summary of Contents for Nighthawk AX6 AX4300



































































































































































Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands

NETGEAR Nighthawk AX6 AX4300, User Manual

Search results

Summary of Contents for Nighthawk AX6 AX4300

Reviews:

Related manuals for Nighthawk AX6 AX4300

Brands by name

Popular brands