manualshive.com logo in svg

NETGEAR MA401 - 802.11b Wireless PC Card, Installation Manual

Share
Download
NETGEAR MA401 - 802.11b Wireless PC Card Installation Manual Download Page 11

8

Setup Instructions 

Use the procedure below that corresponds to the version of Windows you are 
using.

For Windows XP Users Installing a MA401

Note: 

If an earlier version of the Netgear MA401 Wireless PC Card was 

previously installed on your notebook, you must remove the old driver 
and utilities before you can install the new PC Card and software. 

 

Insert the MA401 PC Card into your computer.

a.

Power on your notebook and let the operating system boot up 
completely.

b.

Insert the 

Model MA401 Resource CD

 into your CD-ROM drive. 

c.

Locate an available PCMCIA or CardBus slot on the side of your 
notebook. If your notebook computer has two PCMCIA or CardBus 
slots, the MA401 wireless PC Card can be inserted into either slot.

d.

Hold the PC Card with the Netgear logo facing up and insert it into 
the PC card slot. 

 

 

Summary of Contents for MA401 - 802.11b Wireless PC Card





























Reviews:

No comments

Brands by name

Popular brands

Load more brands