manualshive.com logo in svg

NetComm V200, User Manual, Page: 37 / 65

Share
Download
NetComm V200 User Manual Download Page 37

V200 VoIP Telephone Adaptor/Router 

37

YML795 Rev1 

5.1.4  Call Forward

Call Forward lists the configured call forward information. The first page displays the

current call forward list.  The V200 has two call forwarding entries, which allows you to 

specify call forwarding for each SIP account.  

To modify the call forward list, select the corresponding Select option and then click on the 

Modify

 button.  The Modify Call Forward window is opened.

Field 

Description

Fwd Call

 

Choose YES if you want calls to be forwarded. 

Choose NO if you do not want calls to be forwarded.

User Name

 

SIP user name (VoIP number) to which calls will be 

forwarded to (e.g.09100308).

Host Addr or Domain Name

 

If you use the V200 in SIP proxy mode, this is 

the Domain name in which your V200 currently 

registers. If you use V200 in Non-Proxy mode, this 

is the IP address of the forward-to VoIP ATA or IP 

phone.

Port No

 

The port number at which the remote ATA/IP phone 

or SIP server listen SIP request. Default: 5060

Fwd Uncond

 

If you choose Yes, incoming calls will be forwarded 

to the specified number without ringing on your VoIP

phone. If you choose No, your VoIP phone will ring 

the specific number of times before being forwarded

to the number above.

Fwd Rings

 

The specified number of rings before Unconditional

call forwarding happens.

Summary of Contents for V200


































































Reviews:

No comments