manualshive.com logo in svg

NetComm V200, User Manual, Page: 32 / 65

Share
Download
NetComm V200 User Manual Download Page 32

32

V200 VoIP Telephone Adaptor/Router 

YML795 Rev1

Field 

Description

Auth ID

 

The authentication username assigned by your VoIP 

service provider. This can be a different number to 

your VoIP number.

Auth Password

 

The authentication password assigned by your VoIP 

service provider.

Confirm Password

 

Repeat the password.

Expire

 

Duration of interval for SIP keep alive registration. 

Default 60.

QValue

 

The priority assigned to the V200 to register on the 

SIP server of your VoIP service provider. The value 

must be between 0 and 1, with 1 having the highest 

priority. Default 0.8.

RTP packet interval

 

Duration (frequency) of the V200 sending 

compressed voice data packet. There are two options 

for this setting 20ms and 40ms. In some cases, a 

40ms interval can save your broadband upstream 

bandwidth comparable to a 20ms interval. For the 

best value for this setting, please consult your VoIP 

service provider.

Codec

 

G.729 is the highest compression codec which 

only occupies 8kbits/sec. PCMA (G.711 alaw) and 

PCMU (G.711 ulaw) quire 64kbits/sec. We highly 

recommended you to use G.729. Default G.729.

DTMF

 

In-band or RFC 2833. Default in-band.

Payload Type

 

It indicates which RTP packets contain DTMF 

information in normal RTP stream.

MaxDigist

 

The maximum number of digits (numbers) you can 

dial using the V200. Default 24.

MaxRings

 

The number of rings before an incoming call is 

answered. Maximum 24. Default 15.

Port No

 

The port on the host used to communicate with the 

SIP server or remote end. This port can be changed. 

Default 5060.

UseProxy

 

In order to use the V200 with a VoIP service provider 

you will need to specify a Proxy server which the 

V200 communicates with. Choose Yes and enter 

the details under the Proxy/Register and Domain 

sections. Choose No if you want to use the V200 in 

Peer-to-Peer mode.

Summary of Contents for V200


































































Reviews:

No comments