NetComm NTC-40W, User Manual

Page: 94 / 135

94
NetComm Wireless NTC-40WV Industrial Indoor 3G Router with Voice
www.netcommwireless.com
Ver 1.4
List of get/set commands
The following table is a partial list of get and set commands which may be performed via SMS.
COMMAND
NAME
EXAMPLE DESCRIPTION
get status get status
Returns the Module firmware version, LAN IP Address, Network State, Network operator and
RSSI.
get sessionhistory get sessionhistory
Returns the time and date of recent sessions along with the total amount of data sent and
received for each session.
set syslogserver
set
syslogserver=123.45.67.89:514
Sets a remote syslog server IP or hostname and port.
get plmnscan get plmnscan Instructs the router to perform a network scan and returns the results by SMS.
set forceplmn set forceplmn=505,3
Sets the operator to a manual selection made by the user where “505” is the Mobile Country
Code for Australia and “3” is the Mobile Network Code for Vodafone. As no network type (i.e.
3G or 2G) is specified, it is selected automatically.
get forceplmn get forceplmn
Returns the operator and network type selection mode (Automatic/Manual), in addition to the
MCC and MNC values
get pppoe get pppoe Returns the PPPoE status, currently configured dial string and service name
set pppoe set pppoe=1, telstra.internet, test Sets the PPPoE status on, APN to telstra.internet, and service name to test.
get ledmode get ledmode Returns the status of the LED operation mode.
set ledmode set ledmode=10
Sets the LED operation mode to be always on or to turn off after the specified number of
minutes.
get ssh.proto get ssh.proto Returns the SSH protocol in use.
set ssh.proto set ssh.proto=1,2 Sets the SSH Protocol to protocol 1, 2 or both (1,2).
get ssh.passauth get ssh.passauth Returns the status of the SSH Enable password authentication option.
set ssh.passauth set ssh.passauth=1 Sets the SSH Enable password authentication option on or off.
get.ssh.keyauth get.ssh.keyauth Returns the status of the SSH Enable key authentication option.
set.ssh.keyauth set.ssh.keyauth=1 Sets the SSH Enable key authentication option on or off.
Table 26 - List of get/set commands
List of basic RDB variables
The following table lists valid variables where “x” is a profile number (1-6). If no profile is specified, variables are read from or written
to for the current active profile. If a profile is specified, variables are read from or written to for the specified profile number (‘x’).
# RDB VARIABLE NAME
SMS VARIABLE
NAME
READ/
WRITE
DESCRIPTION EXAMPLE VALUE
0
link.profile.1.enable
link.profile.1.apn
link.profile.1.user
link.profile.1.pass
link.profile.1.auth_type
link.profile.1.iplocal
link.profile.1.status
profile
RW Profile
Read:
(profile no,apn,user,pass,auth,iplocal,status)
1,apn,username,password,
chap,202.44.185.111,up
Write:
(apn, user, pass,auth)
apn,username,password
2 link.profile.1.user username RW 3G username Guest, could also return “null”
3 link.profile.1.pass password RW 3G password Guest, could also return “null”
4 link.profile.1.auth_type authtype RW
3G Authentication
type
”pap” or”chap”
5 link.profile.1.iplocal wanip R WAN IP address 202.44.185.111
6 wwan.0.radio.information.signal_strength rssi R 3G signal strength -65 dBm
7 wwan.0.imei imei R IMEI number 357347050000177
8 statistics.usage_current usage R
3G data usage of
current session
“Rx 500 bytes, Tx 1024 bytes, Total 1524
bytes” or “Rx 0 byte, Tx 0 byte, Total 0 byte”
when wwan down
9
statistics.usage_current
wanuptime R
Up time of current 3G
session 1 days 02:30:12 or 0 days 00:00:00 when
wwan down