manualshive.com logo in svg

NetApp SG100, Hardware Installation And Maintenance Manual

Share
Download
NetApp SG100 Hardware Installation And Maintenance Manual Download Page 57

Deploying a services appliance node

You can deploy a services appliance as a primary Admin Node, a non-primary Admin Node, or a
Gateway Node. Both the SG100 and the SG1000 appliances can operate as Gateway Nodes and
Admin Nodes (primary or non-primary) at the same time.

Deploying a services appliance as a primary Admin Node

When you deploy a services appliance as a primary Admin Node, you use the StorageGRID
Appliance Installer included on the appliance to install the StorageGRID software, or you upload
the software version you want to install. You must install and configure the primary Admin Node
before you install any other appliance node types. A primary Admin Node can connect to the Grid
Network, and to the optional Admin Network and Client Network, if one or both are configured.

Before you begin

•

The appliance has been installed in a rack or cabinet, connected to your networks, and powered
on.

•

Network links, IP addresses, and port remapping (if necessary) have been configured for the
appliance using the StorageGRID Appliance Installer.

Attention: If you have remapped any ports, you
cannot use the same ports to configure load balancer
endpoints. You can create endpoints using remapped
ports, but those endpoints will be remapped to the
original CLB ports and service, not the Load
Balancer service. Follow the steps in the recovery and
maintenance instructions for removing port remaps.

Note: The CLB service is deprecated.

•

You have a service laptop with a supported web browser.

•

You know one of the IP addresses assigned to the appliance. You can use the IP address for any
attached StorageGRID network.

About this task

To install StorageGRID on an appliance primary Admin Node:

•

You use the StorageGRID Appliance Installer to install the StorageGRID software. If you want
to install a different version of the software, you first upload it using the StorageGRID
Appliance Installer.

•

You wait as the software is installed.

•

When the software has been installed, the appliance is rebooted automatically.

Steps

1. Open a browser, and enter the IP address for the appliance.

https://services_appliance_IP:8443

The StorageGRID Appliance Installer Home page appears.

2. In the This Node section, select Primary Admin.

3. In the Node name field, enter the name you want to use for this appliance node, and click

Save.

The node name is assigned to this appliance node in the StorageGRID system. It is shown on
the Grid Nodes page in the Grid Manager.

Hardware Installation and Maintenance Guide for SG100 and SG1000 Appliances 

57

Deploying a services appliance node

Summary of Contents for SG100







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands