FAS2020 System
Installation and Setup
Copyright © 2010 NetApp, Inc. All rights reserved.
Unpack and verify contents
Before you begin
1
2
If you have not already done so, gather the required information and confirm your site
requirements, as described in the Site Requirements Guide at http://now.netapp.com/.
Your system comes with an accessory kit that includes the following components:
- This installation poster
- Power cables
- Software license flyer
- DB-9 to RJ-45 console adapters
- Grounding kit
- Rail kit (for two-post and four-post racks)
Install in rack
3
Caution:
Use only the NetApp
®
rail kit to install your system. Using a different rail kit can cause injury to you or damage to your system.
Four-post rack
Cable the system
4
Cable controllers
Network cable to Remote Management port
4
RJ-45 to DB-9 adapter to console port (required)
1
Fibre
Channel
Ethernet
Console
Remote
Management
Port
Port labels
Network cables to e0a and e0b ports
3
Console cable to adapter
2
Boot the system and proceed with setup
5
- Turn on the power to your system. It takes the LEDs on your system power supplies a few seconds to illuminate.
- Use the console interface and proceed through the setup questions. See the Data ONTAP Software Setup Guide at http://now.netapp.com/.
Cable disk shelves
These are a few common configurations. For additional options, see Supported Configurations for
FAS2000-series Systems at http://now.netapp.com.
or
or
Note:
See the rail kit installation flyer included with the rail kit for the two-post procedure.
210-03961+D0
Mounting
bracket
(2x)
6
e0b
e0a
8
0a
0b
Note: The disk shelf IDs for the
disk shelves should be set in the
range 1 to 6.
1
0
Shelf ID
switch
Setting the disk shelf IDs
e0b
e0a
0a
0b
8
Active/Active NAS or ISCSI:
1 Fibre Channel Disk Shelf Stack (Multipath)
1
Controller to shelf
3
Shelf to controller
2
Shelf to shelf
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
FAS2020
0a
e0a e0b
0b
Controller Module B
0a
e0a e0b
0b
10101
10101
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
FAS2020
0a
e0a e0b
0b
Controller Module B
0a
e0a e0b
0b
10101
10101
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
FAS2020
0a
e0a e0b
0b
Controller Module B
0a
e0a e0b
0b
10101
10101
Controller to shelves
Single Controller Dual Path
1
Controller to shelf
DS14
DS14
PSU
PSU
PSU
PSU
PSU
PSU
FAS2020
0a
e0a e0b
0b
10101
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
Active/Active FC SAN Dual Path
1
2
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
FAS2020
0a
e0a e0b
0b
Controller Module B
0a
e0a e0b
0b
10101
10101
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
DS14
IN
OUT
IN
OUT
PSU
PSU
FAS2020
0a
e0a e0b
0b
Controller Module B
0a
e0a e0b
0b
10101
10101
Connect power
3U
3U
2U
1
1
(2x)
FRONT SIDE
(2x)
Front rail
(2x)
Clip nut (4x)
Controller to switch
e0b
e0a
0a
0b
8
8
e0b
e0a
0a
0b
8
Note:
You do not need to
ground your system.
Trim-17” x 22”
