Netafim SANDSTORM Installation Manual Download Page 9 | Manualshive

Page: 9 / 24

background image

SANDSTORM

™

SINGLE/DOUBLE CHAMBER

INSTALLATION MANUAL | 9

INSTALLATION

NOTE

The manifolds are supported by support legs. Each support leg should be installed immediately after
installing the part it supports. Place the support legs according to their quantity and locations in the
system installation drawings. Use the long support legs to support the inlet manifold, the medium
legs to support the backwash manifold and the short legs to support the outlet manifold.

3.

Connect the inlet manifold to the backwash valves and the inlet manifold sections to each other with

grooved couplings.

4.

Connect the backwash manifold to the backwash valves and the backwash manifold sections to each

other with grooved couplings.

«
...
7
8
9
10
11
...
»

Summary of Contents for SANDSTORM

























Reviews:

No comments

Related manuals for SANDSTORM

Brand: NaturalSof Pages: 12

Brand: Zip Pages: 16

Brand: Waterfilter Pages: 8

Brand: PlasmaMade Pages: 48

CENTRAL Omega HEC-12 PRO Prohibitor

Brand: Tyco Fire Product Pages: 4

Brand: ubbink Pages: 54

Brand: BSVILLAGE Pages: 32

Brand: NELSEN WATER Pages: 12

Pure H2O Series

Brand: Watts Pages: 8

Brand: flamco Pages: 18

Brand: JRC Pages: 4

Traveler TR Series

Brand: Rain Bird Pages: 6

Bacteria Back Country Protection IV Series

Brand: Aquamira Pages: 2

Brand: Aquasafe Pages: 26

Brand: Scottoiler Pages: 1

Brand: Sharp Pages: 2

Brand: Sharp Pages: 2

Brand: Bluewater Pages: 156

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands