manualshive.com logo in svg

Neousys Nuvo-7160GC Series, User Manual

Share
Download
Neousys Nuvo-7160GC Series User Manual Download Page 30

 

 

Nuvo-7160GC/ Nuvo-7164GC Series 

30 

2.3.8 

Reset Button 

 

The reset button is used to manually reset the system in case of system halt or malfunction. To 

avoid unexpected reset, the button is purposely placed behind the panel. To reset, please use 

a pin-like object (eg. tip of a pen) to access the reset button 

2.3.9 

LED Indicators 

 

There are four LED indicators on the I/O panel: IGN, WDT, HDD and PWR. The descriptions 

of these three LED are listed in the following table. 

Indicator 

Color 

Description 

IGN 

Yellow 

Ignition signal indicator, lid when IGN is high (12V/ 24V). 

WDT 

Yellow 

Watchdog timer LED, flashing when WDT is active. 

HDD 

Red 

Hard drive indicator, flashing when hard disk drive is active. 

PWR 

Green 

Power indictor, lid when system is on. 

Summary of Contents for Nuvo-7160GC Series
































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands