Neousys Technology Nuvo-5002E User Manual Download Page 31

Page: 31 / 128

Nuvo-5000 Series User’s Manual

- 31 -

2.3.5 MezIO

I/O Connector

Nuvo-5000 series is designed to incorporate Neousys’ MezIO

interface. You can install a

MezIO

module to expand application-oriented I/O function. To support MezIO

I/O

connectivity, Nuvo-5000 series reserves the cutting hole for a SCSI-II 68-pin connector on

its back panel. Please refer to section 2.5 for information of MezIO

interface and section

3.6 for installing a MezIO

module.

2.3.6 SIM Socket

Nuvo-5000 series provides a panel-accessible SIM socket is on the back panel. Combining

with a 3G/4G module installed on internal mini-PCIe port, you can have Internet access via

telecom operator’s network. The SIM socket is a push-push type. You can insert and push a

SIM card to the end to install it, and push the installed SIM card again to eject it. Please

note that SIM card must be inserted upside down. You can refer to section 3.5 for

information of installing a 3G/4G module and SIM card.

Summary of Contents for Nuvo-5002E

























































































































Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands

Neousys Technology Nuvo-5002E, User Manual

Search results

Summary of Contents for Nuvo-5002E

Reviews:

Related manuals for Nuvo-5002E

Brands by name

Popular brands