NeoDen NeoDen9 User Manual Download Page 37 | Manualshive

Page: 37 / 52

background image

37

Zhejiang Neoden Technology Co., Ltd

Change password:

before Administration login in, this function is not visible.

If the password needs to be changed, please login and click Change password. A window will pop out, enter the original

password. Then follow steps to enter the new password. A successful window will pop out when it’s finished.

Version:

the current software version will be displayed below.

When any software upgrade is required, please copy the upgrade file into the subdirectory of U disk, click “software

upgrade” to load it. Then follow instructions to upgrade it.

English:

this machine supports Chinese and English. To convert it into English, a password is required.

9.1 Feeder Position Config

This interface is used to setup pick offset and test feeding for each feeder.

The left column refers to feeder No., Pick X and Pick Y refer to the coordinates of pick offset. After “click to align”, this

interface will be displayed. Align the center of component (edge of tablet), then save it.

«
...
35
36
37
38
39
...
»

Summary of Contents for NeoDen9





















































Reviews:

No comments

Related manuals for NeoDen9

Brand: Rabe Pages: 65

Brand: Ecco Pages: 3

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: AccuMed Pages: 14

Brand: TAS Pages: 25

Brand: Abicor Binzel Pages: 92

Brand: Gainsborough Pages: 2

Brand: Gainsborough Pages: 2

Brand: Gait up Pages: 12

Brand: Gait up Pages: 6

Brand: Gaiam Pages: 2

Brand: Xtool Pages: 51

Brand: H-TEC Education Pages: 16

Brand: H-TEC Education Pages: 12

Brand: h/p/cosmos Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands