26
Notes
■
The same cooking time can be set automatically for all
hotplates. The set time for each of the hotplates counts down
independently.
The
Basic settings
section contains information on
automatically programming the cooking time.
■
If the combi zone or move function is selected when the
hotplates are combined, the set time is the same for both
hotplates.
Changing or cancelling the time
Selecting the hotplate . Press the
3
symbol and change the
cooking time with the
+
or
-
symbols, or set to
‹‹
.
Once the time has elapsed
The hotplate switches off. A warning signal sounds and
‹‹
appears for 10 seconds in the time program function display.
The
x
indicator on the hotplate lights up. Pressing the
3
symbol turns off the indicators and stops the beeping.
Notes
■
If cooking times have been programmed for various
hotplates, the time programming function always displays the
time for the selected hotplate.
■
Any cooking time can be programmed for up to 99 minutes.
The timer
The timer can be set for periods of up to 99 minutes. It is
independent of the other settings. This function does not
automatically switch off a hotplate.
How to program
No hotplate should be selected.
1.
Press the
3
symbol.
‹‹
and the symbol are shown in the
time program function display
W
2.
Press the
+
or
-
symbols. The basic setting appears.
+
symbol: 10 minutes.
-
symbol: 5 minutes.
3.
Set the desired time using the
+
or
-
symbols.
After a few seconds, the time will start to elapse.
Changing or cancelling the time
Press the
3
symbol several times until the
W
indicator lights
up. Change the time or set it to
‹‹
with the
+
or
-
symbols.
Once the time has elapsed
A warning signal sounds.
‹‹
is displayed on the time program
function display. After 10 seconds the indicators turn off.
Pressing the
3
symbol turns off the indicators and stops the
beeping.
Keep warm function
This function is used for melting chocolate or butter and for
keeping food warm.
To activate
1.
Select the hotplate.
2.
Within the next 10 seconds, press the
–
symbol.
The indicator
–
lights up.
The "keep warm" function will have been activated.
To deactivate
1.
Select the desired hotplate.
2.
Press the
–
symbol.
The
–
indicator disappears.
The hotplate turns off and the residual heat indicator appears.
Cleaning lock function
Cleaning the control panel while the hob is switched on may
change the settings.
In order to avoid this, the hob has a cleaning lock function.
Press the
"
symbol. A signal sounds. The
Ú
indicator lights up
along with the
"
symbol. The control panel is locked for
35 seconds. The control panel surface can now be cleaned
without the risk of changing the settings.
Note:
The lock does not affect the main switch. The hob may
be switched off when desired.
Automatic time limitation
If the hotplate remains in use for a long time and no changes
are made in the settings, the automatic time limitation function
is triggered.
The hotplate stops heating. The
”
,
‰
symbol and the residual
heat indicator
œ
/
•
flash alternately in the display.
The indicator goes out when any symbol is pressed. The
hotplate can now be reset.
When the automatic time function is used, it is governed by the
selected power level (from 1 to 10 hours).
Summary of Contents for T D28 Series
