background image

  Important safety information   

en

21

Note: 

We recommend fitting the appliance such that the 

lower edge of the glass screen is in line with the lower 

edges of the adjacent wall-hung cabinets. Make sure 

that the specified safety clearances from the hob are 

complied with.

(

Important safety 

information

Important safety information

Read these instructions carefully. Only then 

will you be able to operate your appliance 

safely and correctly. Retain the instruction 

manual and installation instructions for future 

use or for subsequent owners.
Check the appliance for damage after 

unpacking it. Do not connect the appliance if it 

has been damaged in transport.
The appliance can only be used safely if it is 

correctly installed according to the safety 

instructions. The installer is responsible for 

ensuring that the appliance works perfectly at 

its installation location.
The surfaces of the appliance are easily 

damaged. Avoid damaging them during 

installation.
The width of the extractor hood must 

correspond at least with the width of the hob.
For the installation, observe the currently valid 

building regulations and the regulations of the 

local electricity and gas suppliers.

:

Warning

Risk of fire!

Fatty deposits in the grease filter may catch 

fire. The specified safety clearances must 

be complied with in order to prevent a build-

up of heat. Refer to the information 

provided for your cooker. If gas and electric 

hobs are being operated together, the 

largest specified clearance applies.

Risk of fire!

Grease deposits in the grease filter may 

catch fire. Never work with naked flames 

close to the appliance (e.g. flambéing). Do 

not install the appliance near a heat-

producing appliance for solid fuel (e.g. 

wood or coal) unless a closed, non-

removable cover is available. There must 

be no flying sparks.

When conveying the exhaust air, official and 

legal regulations (e.g. state building 

regulations) must be followed.

A

B

Summary of Contents for N 90 D95IPU1N0B





























Reviews: