NEFF D36DT57N0, Instruction Manual

Page: 8 / 12

8
Cleaning the metal mesh grease filters
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
:
Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
■
Do not use any aggressive, acidic or alkaline cleaning
agents.
■
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
■
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
By hand:
Note:
You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
In the dishwasher:
Note:
If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
■
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
Installing the metal mesh grease filter
1.
Insert the two metal grease filters under the filter cover with
the lock facing downwards.
Fold the lock downwards and the metal grease filters inwards
and lock them in place.
2.
Insert the metal grease filters on the underside of the
appliance.
3.
Close the filter cover.
4.
Press and hold the 7 button for two seconds.
The saturation indicator is reset.
Changing the activated charcoal filter (only in
circulating-air mode)
In order to guarantee efficient odour filtration, the filter must be
serviced regularly.
The activated charcoal filters must be replaced at least every
4 months.
Notes
■
The activated charcoal filters are not included in the delivery.
The activated charcoal filters can be obtained from specialist
retailers, from our after-sales service or from the Online Shop.
■
The activated charcoal filters cannot be cleaned or
reactivated.
1.
Remove the metal grease filters.
2.
Turn the old activated charcoal filters and pull away from the
holder. ¨
3.
Push the new activated charcoal filters onto the holder and
turn. ©
4.
Install the metal grease filters.
5.
Reset the saturation indicator; see section Saturation
indicator .
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
:
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a licensed
technician (electrician).
Malfunction table
--------
% $
Problem Possible cause Solution
The appliance
does not work
The plug is not
plugged in.
Connect the appliance to
the electricity supply
Power cut Check whether other
kitchen appliances are
working
Faulty fuse Check in the fuse box to
make sure that the fuse for
the appliance is OK
The button illu-
mination does
not work.
The control unit
is faulty.
Call the after ­ sales service.
The lighting
does not work.
The LED lights
are defective.
Call the after-sales service.
ª or ’ appears
on the display
The grease filter
or the activated
charcoal filter is
saturated.
To clean the grease filter or
change the activated char-
coal filter, see Chapter
Cleaning and maintenance .