24
Troubleshooting
Malfunctions often have simple explanations. Please read the
following instructions before calling the after-sales service.
Repairs may only be carried out by fully trained after-sales
service technicians. Incorrect repairs to your appliance may
present considerable risks for the user.
ã=
Risk of electric shock!
■
Work on the appliance electronics may only be performed by
a specialist.
■
Always disconnect the appliance from the power supply
when work is carried out on the electronics. Switch off the
circuit breaker or remove the fuse from your household fuse
box.
Problem
Possible cause
Notes/remedy
The appliance does not work
The plug is not plugged into the mains.
Connect the appliance to the electricity
supply
Power cut
Check whether other kitchen appliances
are working
Fuse defective
Check in the fuse box to make sure that
the fuse for the appliance is OK
Faulty operation
Switch the appliance off using the fuse in
the fuse box. Wait approximately 10 sec-
onds and then switch it back on.
The appliance cannot be started
The appliance door is not fully closed
Close the appliance door
The appliance cannot be started. “Des-
cale“ appears in the text display.
Descaling has been cancelled
Press the Start button. Then rinse the
appliance twice (see section: Descaling).
Proceed as described under "Emptying
the evaporator dish and refilling the water
tank")
The appliance cannot be started. “Clean“
appears in the text display.
Cleaning aid was cancelled
Press the Start button. Then rinse the
appliance twice (see section: Cleaning aid
EasyClean®. Proceed as described in the
section “Emptying the evaporator dish and
wiping out the appliance”)
‹
:
‹‹
flashes in the clock display
Power cut
Reset the clock (see section: Electronic
clock)
‹
:
‹‹
flashes on the clock display,
§§§
appears on the temperature display
Power cut during cooking
Press the
KJ
clock function button, reset
the clock (see section: Electronic clock)
The appliance is not in operation. A cook-
ing time is shown on the display.
The Start button was not pressed after the
setting had been made.
Press the Start button or delete the setting
with the Stop button
"Safety cut-out" appears in the text display
and
‹‹‹
flashes in the temperature dis-
play
Automatic Safety cut-out is active
Turn the operating mode selector back to
the
Û
position
“Fill water tank” appears even though the
water tank is full
The water tank has not been inserted
properly
Slide in the water tank until it engages.
The detection system is not working
Call the after-sales service
“Fill water tank” appears even though the
water tank is not yet empty, or the water
tank is empty but “Fill water tank” does not
appear
The water tank is dirty. The mobile water
level indicators are jammed
Shake and clean the water tank. If the
parts cannot be released, obtain a new
water tank from the after-sales service.
The water tank drains for no discernible
reason. The evaporator dish is overflowing
The water tank was not closed properly
Close the lid until you feel it engage.
The tank lid seal is dirty
Clean the seal
The seal in the tank cover is defective
Obtain a new water tank from the after-
sales service
The evaporator dish has boiled empty
even though the water tank is full.
The water tank has not been inserted
properly
Slide in the water tank until it engages
The feed line is blocked
Descale the appliance. Check whether the
water hardness range is set correctly
"Empty/Clean tank?" appears in the dis-
play
The appliance has not been used for at
least two days and the water tank is full
Empty and clean the water tank. Always
empty the water tank after cooking
There is a “pop” noise during cooking
Cold/warm effect with frozen food, caused
by the steam
This is normal.
When you cook with steam, a lot of steam
is created
The appliance is being automatically cali-
brated
This is normal.
