10
Switching off the appliance
ã=
Risk of scalding!
When opening the appliance door, hot steam may escape.
After cooking, only open the appliance door carefully.
Note:
The appliance has a cooling fan. After the appliance is
switched off, the cooling fan may continue to run.
1.
Turn the operating mode selector back to the off position
Û
.
2.
Press on the operating mode selector until it retracts.
The appliance switches off. The
~
symbol goes out.
Note:
If the appliance is switched off after steam-assisted
operation, you will hear a pumping sound. The appliance is
pumping the remaining water out of the evaporator system
back into the water tank. During this time the
Ì
symbol is lit.
Only empty the water tank when the
Ì
symbol is no longer lit.
You can see in the temperature display whether there is high or
low residual heat in the cooking compartment.
Ending an operation
Press and hold the
„
Stop button. The appliance turns off the
current operation. The appliance is not switched off. You can
now start another operating mode.
Interrupting and continuing an operation (Pause)
Briefly press the
„
Stop button. The appliance interrupts the
current operation. Press the
ƒ
Start button to continue the
operation.
After each use with steam assistance
1.
Switch off the appliance.
The remaining water will be pumped out of the evaporator
system and back into the water tank. The
Ì
symbol lights up
during this time.
2.
Only empty the water tank when the
Ì
symbol is no longer
lit.
3.
Empty and clean the water tank and allow it to dry with the
door open.
4.
Dry the cold cooking compartment with a soft cloth.
5.
Remove any dirt from the cooking compartment.
Note:
Remove limescale with a cloth soaked in vinegar, then
wipe with clean water and rub dry with a soft cloth.
Automatic safety cut-out
The automatic safety cut-out is activated if your appliance is
switched on and you have not made any settings for a long
time.
The length of time after which your appliance switches itself off
depends on the settings that you make.
‹‹‹
flashes in the temperature display. Appliance operation is
interrupted.
Turn the operating mode selector to the
Û
position to
deactivate it.
Changing the Basic settings
Your appliance has various Basic settings, which are preset at
the factory. You can, however, change these Basic settings as
required.
1.
Switch on the appliance.
2.
Press and hold the
±
info button for 3 seconds to go to
the Basic settings menu.
™‚‹
appears in the display (appliance unlocked).
3.
Press the
±
info button repeatedly until the setting symbol for
the current basic setting of a submenu appears in the
temperature display (e.g.
™„ƒ
Audible signal 2 minutes).
4.
Use the temperature selector to set the required basic setting
within a submenu (e.g.
™„„
Audible signal 10 minutes).
5.
Press and hold the
±
info button for 3 seconds.
Your basic setting is saved.
Note:
If you do not make any changes within 15 seconds, the
appliance automatically exits the Basic settings menu.
You can change the following Basic settings:
Temperature dis-
play
Meaning
•
Residual heat high (above 120 °C)
œ
Residual heat low (between
60 °C and 120 °C)
Basic settings menu
Submenu
Basic setting
Setting
symbol
Childproof lock
Appliance unlocked
™‚‹
Appliance locked
™‚‚
Appliance permanently
locked
™ƒ‚
Audible signal
Audible signal off
™„‹
Audible signal
30 seconds
™„‚
Audible signal 2 minutes
™„ƒ
Audible signal
10 minutes
™„„
Water hardness
softened
™…‹
soft
™…‚
medium
™…ƒ
hard
™…„
