NED CAMERA Link Ryugan RCDL2K20CL User Manual Download Page 22

Page: 22 / 72

NED

RCDL2K20CL

UME-0115-02

3 Hardware

3.1 Camera Connection

In order to use the camera, the following steps are required.

1. Connect the camera to the frame grabber board (image acquisition board) using a

Camera Link-compatible cable.

A single Camera Link compatible cable is used to connect the camera and frame

grabber board.

When using a directional Camera Link compatible cable, connect the connector

labeled "Camera side" to the camera.

2. Connect to the power supply.

Use the power cable to connect the camera to the power supply for the camera.

Connect the plug side of the power cable to the camera, and connect the

unprocessed side to the power supply for the camera. In addition to the above, a

personal computer, frame grabber board, imaging lens, lens mount, light source,

encoder, etc. are required. Select the appropriate one for your purpose and

configure it appropriately.

Camera Link

Frame Grabber Board

Line Scan Camera

Camera Link Cable

Power Cable

Camera

Power Supply

DC+12V 15W

CL1

Figure 3-1-1 Connections between Camera and Frame Grabber Board and Power Supply

Camera Link cable manufacturers may have two types of cable for the Camera Link

Base Configuration board. See the specification and choose the appropriate cable.

Summary of Contents for CAMERA Link Ryugan RCDL2K20CL









































































Search results

Summary of Contents for CAMERA Link Ryugan RCDL2K20CL

Reviews:

Related manuals for CAMERA Link Ryugan RCDL2K20CL

Brands by name

Popular brands

NED CAMERA Link Ryugan RCDL2K20CL, User Manual

Search results

Summary of Contents for CAMERA Link Ryugan RCDL2K20CL

Reviews:

Related manuals for CAMERA Link Ryugan RCDL2K20CL

Brands by name

Popular brands