manualshive.com logo in svg

NEC Univerge UM8000, Installation Manual

Share
Download
NEC Univerge UM8000 Installation Manual Download Page 105

UM8000

Issue No. 1.0

Installation Manual

12 - 3

2.1.3

Downloading a Backup Stored on the Voice Mail Drive

To download a backup stored on the voice mail drive, perform the 
following steps:

1.

Log into the Web Admin Console (WAC).

2.

Go to System/Backup and Restore/Restore.

3.

In the Action pull down menu choose 

Download

.

4.

If prompted by the Internet browser, choose to allow the 
download.

5.

Choose to 

Save

 the backup zip file.

6.

Browse to the location where the file is to be downloaded on the 
support PC.

7.

Click 

Save

.

2.2

Restoring a Database Back Up to the UM8000

2.2.1

Uploading a Stored Backup to the Voice Mail Drive

To upload a stored backup to the voice mail drive, perform the 
following steps:

1.

Log into the Web Admin Console (WAC).

2.

Go to System/Backup and Restore/Restore.

3.

Under Upload an existing backup to the messaging system, click 
on 

browse

.

4.

Browse to the location where file is to be stored on the support 
PC.

5.

Click 

Upload File

.

2.2.2

Restoring a Previous Backup

To restore a previous backup, perform the following steps:

1.

Log in to the Web Admin Console (WAC).

2.

Go to Server Control.

3.

If started, choose to stop the server.

4.

Go to System/Backup and Restore/Restore.

5.

In the Action pull down menu, choose 

Restore this backup

.

6.

If the backup has messages, confirm you want the messages 
restored with the database.

Summary of Contents for Univerge UM8000



































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands