manualshive.com logo in svg

NEC T30A, User Manual

Share
Download
NEC T30A User Manual Download Page 76

-49- 

 

 

4.4.2.1

 

Library Settings 

 

Table 4-13 Library Setting Submenu 

Submenu item 

Default 

Description 

I/O Station 

Disable 

Enable or disable the I/O station. 

Active Slots 

T30A:30 
T60A:60 

Sets the number of data slots and the active/inactive setting.   
Each logical library can be set.   

Auto Cleaning Mode 

Disable 

Enable or disable auto cleaning.   
Each logical library can be set. 
For auto cleaning to be executed, an Inactive slot must be set 
in advance. 

Library Mode 

Random Mode 

This  submenu  can  be  used  to  switch  between  random  and 
sequential mode. 
Sequential mode should be set when used in environments in 
which the Accessor cannot be controlled.   

・

Random Mode 

Random mode should be set when using backup software.   
Sequential Mode 
-Loop Mode 
Operation does not stop after the cartridge has been unloaded 
by the host from the last slot. Instead, the first slot's cartridge 
is loaded, and then operation continues. 
-Auto Load Mode 
When  the  magazine  is  set  to  the  Library,  the  cartridge  is 
automatically mounted in the drive.   

Cleaning Notice 

- 

This  submenu  can  be  used  to  setup  the  SNMP  about 
Cleaning. 

・

Nearly Expired 

  Nearly Expired trap is reported from setup value to 1. 
  Setup value:1-49 
 

・

Every Cleaning 

  Set up whether it remains for every cleaning execution 
  and report the number of times trap. 

Apply 

- 

The above-mentioned setting is applied. 

 

 

Auto Cleaning Mode

：

 

When you use the library with backup software, please set up an Auto Cleaning 
Mode Disable. 
If  the  backup  software  supports  the  AUTO  CLEANING  Mode,  use  the  auto 
cleaning function of backup software.

 

 

Summary of Contents for T30A





























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands