NEC T30A User Manual Download Page 200

Page: 200 / 252

-173-

10.5

Replacing the Drive Module

The drive module replacement procedure is the same for all drive types.

The supervisory service of all the services of backup software, a tape, and a changer driver is

suspended.The Windows version Networker stops a server.

If there is a cartridge in the drive, move it to the magazine slot by using the backup software or by

using the operating panel.

Remove the interface cable connected to the drive to be replaced.

[Service Login] in Operator panel. See Section 4.3.1

Service Login

for detail.

Select [Drive Replacement] from [Service].

Select the drive to exchange and select Remove Drive.

Unfasten the two screws shown below and extract the drive to be replaced.

Mount the new drive and anchor it with two screws shown above.

Select [Drive Replacement] from [Service].

10.

Select the drive exchanged and select Restore Drive.

11.

It is checked whether a serial number is succeeded before and after drive exchange.
[Yes] is chosen when succeeding a serial number before and after drive exchange.
[No] is chosen when not succeeding a serial number before and after drive exchange.

12.

Restore the maintenance information, referring to "10.1.2 Restoring Maintenance Information".

13.

From the operator panel, confirm that the drive has been recognized.

14.

Connect the interface cable to the new drive.

15.

Perform drive diagnostics, referring to "9.2

Diagnosis test

Screws

Summary of Contents for T30A





























































































































































































































































Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands

NEC T30A, User Manual

Search results

Summary of Contents for T30A

Reviews:

Related manuals for T30A

Brands by name

Popular brands