NEC T30A User Manual Download Page 193 | Manualshive

Page: 193 / 252

background image

-166-

9.8

Moving the Library

Please follow the following procedure when moving or transporting this machine.

When shutting down the system, refer to “

1)

[Login]. See Section 4.3Login for detail.

2)

If there is a cartridge in the drive, first unload it (eject), and then move it to the magazine slot.
Either consult the back up software manual or use the front panel keys.

（

See “4.7.2Removing

3)

Remove the cartridge from magazine.(See “4.6.1Magazine

4)

Execute [Shipping move] of [Commands] from operator panel.

5)

Confirm the display of [Tighten the shipping Screw and Turn the Power] and tighten the screw
for transportation on the back of machine.

※

Do the following work even when you cannot tighten the screw.

6)

Turn OFF the power switch of the machine.

7)

Remove the AC Power Cable, Interface Cable.

Do not turn off the power switch of the machine if the interface is in inactive
state. If you turn off the power switch of the device while the bus is in active State,
there is a risk of data loss or unstable bus state. If the system needs to be switched
off and is still connected to the LAN, then contact the administrator before
switching off.

When you are transporting this machine, please re-pack it in the packaging material
and in the same way it was packed at the time of purchase. If you do not have the
packaging. material, then transport the machine in soft cushioning material in order
to protect from shocks.

«
...
191
192
193
194
195
...
»

Summary of Contents for T30A





























































































































































































































































Reviews:

No comments

Related manuals for T30A

Brand: Oki Pages: 16

NBX V3000 Analog

Brand: 3Com Pages: 2

OfficeConnect 3C19500

Brand: 3Com Pages: 52

Brand: Ykk ap Pages: 36

Brand: Oki Pages: 16

Brand: FRANKLINWH Pages: 81

Brand: Kreg Pages: 32

Brand: PowerTec Pages: 40

Brand: Kval Pages: 72

Brand: Okofen Pages: 16

WD SATA Hard Drives

Brand: Western Digital Pages: 2

Brand: Datoptic Pages: 1

WOODEN WORK BENCH

Brand: Discovery Kids Pages: 9

Brand: Promise Technology Pages: 170

Brand: Tektronix Pages: 20

Brand: SEI Pages: 5

Brand: LaCie Pages: 2

Brand: morse Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands