background image

ISSUED: 11-01-06  SHEET #: 055-9478-6    01-14-09

Visit the Peerless Web Site at www.peerlessmounts.com

1 of 8

For customer care call 1-800-729-0307 or 708-865-8870.

 Read instruction sheet before you start installation and assembly.

Maximum Load Capacity: 50 lb (22.7 kg)

IMPORTANT! Be sure not to touch the projector while tightening the set screw on the
ball and socket mount. This may cause the image to be unaligned when you let go.

Applications:

Flush Mount .................................................................................................................................................. page 5

Extension Column ........................................................................................................................................ page 6

Installations:

To Wood Joist Finished Ceilings,
Exposed Wood Joists, or Wood Beam Ceilings ........................................................................................ page 3

To Concrete Ceilings .................................................................................................................................... page 4

IMPORTANT!  Turn to the appropriate page for your ceiling installation.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and

components.

WARNING

R

This product is intended for use with UL
Listed products and must be installed by a
qualified professional installer.

NEC DISPLAY SOLUTIONS OF AMERICA, INC.

Model:  NP40CM

Installation and Assembly -Ceiling Mount for
NEC NP 40/41/50/60/61/62/100/200 Projectors 

Summary of Contents for NP40CM









Reviews: