NEC NC1000C Installation Manual Download Page 69

Page: 69 / 97

LCD Menu

4-3-3. Reset

Used when initializing settings and usage times. Some of the items are in the service personnel menu. Refer to “4-1-1. When You
Use the Service Personnel Menu” (page 66) for details on how to use these.

Item

Service Personnel

User

FactoryDefalut



—

Lamp Usage



Filter Usage



Filter Cleaning



Fan Usage



—

Douser Count



—

FactoryDefault

Returns the projector main unit settings to the factory default state. You can choose from the following three types of methods.

•

Registered preset buttons and title settings

•

Network settings

•

All adjustment and setting values

←

Select the item to be reset.

←

Press the ENTER button to execute resetting.

P Button & Title

Resets the allocation of preset buttons and all registered titles.

LAN

Resets the network settings.

All

Resets all adjustment and setting values.

NOTE

If you are logged in to the projector with Installation privileges, you cannot reset the network settings (LAN).

Summary of Contents for NC1000C


































































































Search results

Summary of Contents for NC1000C

Reviews:

Related manuals for NC1000C

Brands by name

Popular brands

NEC NC1000C, Installation Manual

Search results

Summary of Contents for NC1000C

Reviews:

Related manuals for NC1000C

Brands by name

Popular brands