NEC NC1000C Installation Manual Download Page 59 | Manualshive

Page: 59 / 97

background image

59

Projector Adjustment and Connecting

3-7. Replacing the Notch Filter

This projector is equipped with a notch filter that has been optimized for projection in a movie theater. The image can be made
brighter by removing the notch filter. Note that the projector does not comply with the Color Gamut in the DCI standards in that
case.

NOTE

If you remove the notch filter, always attach the dummy bracket.

Preparation:

•

Phillips head screwdriver (No.2).

•

Turn off the projector and disconnect it from the electrical outlet.

1

Remove the notch filter cover.

1. Loosen the screw. The screw cannot be removed.

2. Open the notch filter cover, and then pull it up and remove it.

«
...
57
58
59
60
61
...
»

Summary of Contents for NC1000C


































































































Reviews:

No comments

Related manuals for NC1000C

Brand: Panamax Pages: 2

Christie DS+10K-J

Brand: Christie Pages: 77

Brand: Projectiondesign Pages: 33

Brand: Light Sky Pages: 26

Brand: JAROLIFT Pages: 37

Reflection VX-5c

Brand: Runco Pages: 131

Brand: Radiola Pages: 48

VirtuaLine SWITCH LED

Brand: Laserglow Pages: 13

Brand: InFocus Pages: 4

Brand: Hitachi Pages: 55

Illumina PJ-TX10

Brand: Hitachi Pages: 53

Brand: Panasonic Pages: 28

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 2

Brand: Philips Pages: 10

Brand: Philips Pages: 10

Brand: Sanyo Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands