NEC NC1000C Installation Manual Download Page 25

Page: 25 / 97

Before Setting Up Your Projector

1-5. Removing the Projector Covers

This section provides guideline information on how to mount and remove covers on the projector.

Name of the cover

Side cover

Notch filter cover

Filter cover (side)

Front cover

Filter cover (rear)

Lamp cover

NOTE

•

“Side cover” and “Front cover” are equipped with key locks. Special keys (cover key) are required to mount or
remove them.

•

To remove the side cover, the filter cover (side) needs to be removed.

•

If you remove the front cover or side cover, the following error message is displayed on the LCD screen of the main
unit operating panel by the tamper detection circuit.
“Tamper Fail”, “Service Door Tamper”

Encrypted contents cannot be displayed while an error message is being displayed. Refer to “3-2. Recovering from
Tamper Errors” (page 49) for the recovery procedure.

Summary of Contents for NC1000C


































































































Search results

Summary of Contents for NC1000C

Reviews:

Related manuals for NC1000C

Brands by name

Popular brands

NEC NC1000C, Installation Manual

Search results

Summary of Contents for NC1000C

Reviews:

Related manuals for NC1000C

Brands by name

Popular brands