N8151-141/142/143 Internal LTO5/6/7
Read me first
GZS-000649-002-01
December 2017 Second edition
Please keep this document carefully.
Be sure to read this Startup Guide carefully before using this product and retain it for reference.
This document provides information required to your product safely and properly.
Keep this document nearby so that you may use refer to it as necessary. Before using this product, be sure to read this guide
and
“
User
’
s Manual
”
(in website :
http://www.nec.com/express/
).
SAFETY INDICATIONS
This Safety Precautions describes the device components with possible danger, hazards that may be caused by ignoring warnings,
and preventive actions against such hazards.
Components with possible danger are indicated with a warning label placed on or around them. In the User's Guide or warning
labels, "Warning" or "Caution" is used to indicate a degree of danger. These terms are defined as follows:
Indicates there is a risk of death or serious personal injury
Indicates there is a risk of burns, other personal injury, or property damage
Precautions and notices against hazards are presented with one of the following three symbols. The individual symbols are defined
as follows:
Attention
This symbol indicates the presence of a hazard if the instruction is ignored.
An image in the symbol illustrates the hazard type.
(Example)
(Electric shock Risk)
Prohibited
Action
This symbol indicates prohibited actions.
An image in the symbol illustrates a particular prohibited action.
(Example)
(Do not disassemble)
Mandatory
Action
This symbol indicates mandatory actions.
An image in the symbol illustrates a mandatory action to avoid a particular
hazard.
(Example)
(Disconnect a plug)
Symbols to draw attention Description of warning A term indicating a degree of danger
Do not install the device while the power is on.
Unplug the AC power cord from the main power source when installing/uninstalling the device to/from basic processing
unit or connect it with the enclosure. Failure to follow this warning may cause an electric shock.
SYMBOLS USED IN THIS USER'S GUIDE AND WARNING LABELS
Attention
Indicates that improper use may cause an electric
shock.
Indicates that improper use may cause fumes or fire.
Indicates that improper use may cause fingers to be
caught.
Indicates a non-particular notice or warning.
Indicates that improper use may cause personal injury
due to high temperature.
Prohibited Action
Indicates a non-particular and mandatory action.
Do not disassemble, repair, or modify the device.
Otherwise, an electric shock or fire may be caused.
Do not touch by the wet hand. Otherwise, an electric
shock may be caused.
Do not touch any component other than specified.
Otherwise, an electric shock or personal injury such as
bums may be caused.
Mandatory Action
Unplug the power cord. Otherwise, an electric shock or
fire may be caused.
Indicates a non-particular and mandatory action. Make
sure to follow the instruction.
NOTES SAFETY
General Attention
Do not use in life-critical applications or applications requiring
high reliability.
This device is not intended for integration with or control of facilities or
equipment that may affect human life or that require a high degree of
reliability, such as medical equipment, nuclear power facilities,
aerospace instruments, and transportation equipment. The
manufacturer does not assume any liability for accidents resulting in
injury or death, or for any damages to property that may occur as a result
of using this device in such facilities, equipment, or control systems.
Do not use the Internal LTO if any smoke, odor, or noise is present.
If smoke, odor, or noise is present, immediately turn off the POWER
switch and disconnect the power plug from the outlet, then contact your
sales agent. Using the Internal LTO in such conditions may cause a fire.
Keep needles or metal objects away from the Internal LTO.
Do not insert needles or metal objects into ventilation holes in the
Internal LTO. Failure to follow this warning may cause an electric shock.
Keep water or foreign matter away from the Internal LTO.
Do not let any kind of liquid (water etc.) or foreign matter (e.g., pins or
paper clips) enter the Internal LTO. Failure to follow this warning may
cause an electric shock, a fire, or a failure of the Internal LTO. When
such things accidentally enter the Internal LTO, immediately turn off the
power and disconnect the power plug from the outlet. Do not
disassemble the Internal LTO. Contact your sales agent.
Attention to Installing, Moving, Storing, Connection
Do not close the ventilation hole.
Do not close the ventilation hole in the front side of the Internal LTO.
Otherwise, Its internal temperature will rise to cause malfunctions or a
fire.
Do not connect/disconnect the interface cables before unplugging
the power plug.
Before connecting/disconnecting the interface cables, disconnect the
power plug of the main power unit from the outlet. If the power is off but
the power plug is still connected, you may get an electric shock.
Do not use the unspecified interface cables.
Use only the cable authorized by NEC and locate the device and
connector before connection. Use of an unauthorized cable or displaced
connection may cause a short circuit, resulting in a fire.
When handling or connecting the interface cables, keep the notes as
follows:
■
Do not tread on cables.
■
Do not load on the cable.
■
Insert the cable connector as far as it goes.
■
Do not use damaged cables.
■
Do not use damaged connectors.
Do not use the equipment in the place where corrosive gases exist.
Do not use Built- In LTO Auto Loader, installing in the environment
where corrosive gas (sulfur dioxide, hydrogen sulfide, nitrogen dioxide,
chlorine, ammonia, ozone, etc.) exists.
In addition, do not set it up in the environment including the element
(sodium chloride and sulfur, etc.) that promotes corrosion in dust and
air, and the electro-conductive metal etc. The print plate in the device
corrodes, and it might cause the breakdown and smoking and the
ignition.
When there is the above-mentioned doubt in the environment of use,
please consult with a store or a maintenance service company.
Avoid installation in extreme temperature condition.
Immediately after the power supply of the server is turned off,
components in the server including the internal hard disk drive or others
are hot. Please install/detach the device after confirming it is cold
enough.
Attention to Operation
Do not insert your hands into the cartridge load compartment.
Do not insert your hands into the cartridge load compartment.
Otherwise, the fingers will be caught/pinched by the Internal LTO to
cause an injury.
Do not touch the Internal LTO when it thunders.
If it starts thundering, do not touch any part of the Internal LTO. Failure
to follow this warning may cause an electric shock or a fire.
Keep away pets.
Keep away pets from the Internal LTO. Insertion their hair or excrements
may cause a fire or an electric shock.
Attention to Power or Power Cord
Do not hold the DC cable with a wet hand.
Do not disconnect/connect the cable while your hands are wet. Failure
to follow this warning may cause an electric shock.
Do not install the device while the power is turned on.
Unplug the AC power cord from the main power source when
installing/uninstalling the device to/from server or connect it with the
enclosure. Failure to follow this warning may cause an electric shock.
Insert the DC cable into the outlet as far as it goes.
Heat generation resulting from a halfway inserted DC cable (imperfect
contact) may cause a fire. Heat will also be generated if condensation
is formed on dusty blades of the halfway inserted cable, increasing the
possibility of a fire.
Do not connect the Internal LTO by unspecified cabling.
Connecting or cabling with DC cable should be done in accordance with
the procedure specified in the User's Guide.
Unspecified connecting or cabling may cause an electric shock or a fire.
Do not use any damaged power cord.
If the power cord is damaged, immediately replace it with a new part of
same type. Do not repair the damaged section for reuse. Otherwise, the
section repaired with vinyl tape or the like will be overheated to cause
an electric shock or a fire.
Use the authorized cable only.
Use only the specified cable when connecting the Internal LTO with a
server. Use of an unspecified cable or connection by unspecified cabling
may cause a fire.
Attention to Handling or Maintenance
Do not disassemble, repair, or alter the Internal LTO.
Never attempt to disassemble, repair, or alter the Internal LTO
on any occasion other than described in this User’s Guide. Failure to
follow this instruction may cause an electric shock or a fire as well as
malfunctions of the Internal LTO.
Do not handle while the power plug is connected.
Before handling or cleaning the Internal LTO, disconnect the power plug
of the main power unit from the outlet. If the power is off but the power
plug is still connected, you may get an electric shock or may cause a
fire by short-circuit.
Insert the cables into the connectors as far as it goes.
Heat generation resulting from a halfway inserted cables or Interface
cables (imperfect contact) may cause a fire. Heat will also be generated
if condensation is formed on dusty blades of the halfway inserted cable,
increasing the possibility of a fire.
This product contains code compliant with GPL and / or LGPL.
Please refer to download the product documentation to be
applicable from the following URL for the availability of source
code.
http://www.nec.com/express/
If you have any questions on the contents of this document,
please contact the dealer where you purchased the product
or our sales representative.
Detailed handling of this device is described in the User's
Guide.
Please download the User's Guide for the appropriate product
from the following URL.
http://www.nec.com/express/
Please also read the sure User's Guide before using this
equipment.
Printed on recycled paper
© NEC Corporation 2017
No copying or modifying without permission of NEC Corporation.
The contents of this document may be changed without notice.
