NEC MuPD70F3187 User Manual Download Page 574 | Manualshive

Page: 574 / 1053

background image

574

Chapter 14

A/D Converter

User’s Manual U16580EE3V1UD00

14.2 Configuration

The A/D converter of the V850E/PH2 adopts the successive approximation method, and uses A/D con-
verter n mode registers 0, 1, 2 (ADMn0, ADMn1, ADMn2), and the A/D conversion result register
(ADCRn0 to ADCRn9) to perform A/D conversion operations (n = 0, 1).

(1)

Input circuit

The input circuit selects the analog input (ANIn0 to ANIn9) according to the mode set by the
ADMn0, ADMn1, and ADMn2 registers.

(2)

C-Array

Holds the charge of the differential voltage between the voltage input from the analog input pins
(ANIn0 to ANIn9) and the reference voltage (1/2 AV

DD

), and redistributes the sampled charges.

(3)

C-Dummy

This block holds the reference voltage (1/2 AV

DD

) and assigns the reference of the comparator

input.

(4)

Voltage comparator

The voltage comparator compares the C-Array comparison potential with the C-Dummy reference
potential.

(5)

A/D conversion result register (ADCRnm), A/D conversion result register nH (ADCRnmH)
(n = 0, 1)(m = 0 to 9)

ADCRnm is a 10-bit register that holds A/D conversion results. Each time A/D conversion is
completed, the conversion results are loaded from the successive approximation register (SAR).
RESET input makes this register undefined.

(6)

A/D conversion result register for DMA transfer (ADDMAn) (n = 0, 1)

ADDMAn is a 16-bit register that holds the last 10-bit A/D conversion result and an over rung flag
for indicating a DMA transfer failure.

(7)

ANIn0 to ANIn9 pins (n = 0, 1)

These are 10-channel analog input pins for the A/D converter n. They input the analog signals to
be A/D converted.

Caution:

Make sure that the voltages input to ANIn0 to ANIn9 do not exceed the rated values. If
a voltage higher than AV

DD

or lower than AV

SSn

(even within the range of the absolute

maximum ratings) is input to a channel, the conversion value of the channel is
undefined, and the conversion values of the other channels may also be affected.

(8)

AV

REFn

pins (n = 0, 1)

This is the pin for inputting the reference voltage of the A/D converter. It converts signals input to
the ANIn0 to ANIn9 pins to digital signals based on the voltage applied between AV

SSn

and

AV

REFn

.

«
...
572
573
574
575
576
...
»

Summary of Contents for MuPD70F3187






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MuPD70F3187

Brand: Hafele Pages: 82

Brand: Danfoss Pages: 32

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 4

ECL Comfort 110

Brand: Danfoss Pages: 2

UTAdvanced UT35A

Brand: YOKOGAWA Pages: 18

Brand: DeLaval Pages: 102

Brand: Auber Pages: 3

TRIO MPC-165 Series

Brand: Sutter Instrument Pages: 60

VARIOMATIC SARV 07.1

Brand: AUMA Pages: 32

Brand: YASKAWA Pages: 12

Brand: Gateway Pages: 2

Brand: Oriental motor Pages: 4

Brand: Eaton Pages: 2

Cutler-Hammer S701X25N3BP

Brand: Eaton Pages: 4

Alicat Scientific IVCD

Brand: Halma Pages: 28

Brand: Minebea Intec Pages: 138

DuoControl horizontal

Brand: Truma Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands