NEC M166C Customer Engineer Manual Download Page 46

Page: 46 / 56

How to Setup Tyco/Elpas

Page

M166 CE Manual

7.2

Installing the DLA card in the M166CL

Use the following procedure to install the DLA card.

PROCEDURE:

How to install the DLA in the M166

Actions

Make sure that your M166 is type M166CL. If not, you cannot install the DLA card.

Make sure tha the M166 is switched off.

Open the rear side of the M166CL by means of removing the two screws as shown
in the following picture:

Mount the DLA card on to the M166, as shown in the picture below.

Note:

Please be very careful in installing the DLA in the M166.

Note:

The holes in the DLA card should fit over the rings in the M166, as shown in the

picture below.

Note:

There are 6 pins on the DLA that should fit into the six pins connector in the

M166.

Note:

Do not use force.

Remove two screws to get access to

the DLA compartment.

Summary of Contents for M166C

























































Search results

Summary of Contents for M166C

Reviews:

Related manuals for M166C

Brands by name

Popular brands

NEC M166C, Customer Engineer Manual

Search results

Summary of Contents for M166C

Reviews:

Related manuals for M166C

Brands by name

Popular brands