4
1
<Unpairing>
To unpair a paired the Bluetooth
®
device, select the device in the [Delete] screen.
▼
Other Setting and Check
<Visibility Setting>
Set whether to make information about the IP3NA-BCH ADAPTER( ) visible to other Bluetooth
®
devices
(default: [1. Disable]).
<BT Information>
You can view the following kinds of information about the IP3NA-BCH ADAPTER( ):
・
Firmware and hardware versions
・
Bluetooth
®
module information and
standard
・
Installed profile versions
・
Device address and name
▼
Specifications
※
Bluetooth
®
is a registered trademark owned by Bluetooth SIG, Inc. and is licensed to NEC Infrontia
Corporation.
▼
Introduction
The IP3NA-BCH ADAPTER( ) is an adapter that connects a Bluetooth
®
device to a multifunctional tele-
phone.
The table below lists the type of device that can be connected to the IP3NA-BCH ADAPTER( ) and the
functions supported by it.
Item
Specification
Destination
Multifunctional telephone bottom-unit connector (except for economy multifunctional telephone)
Bluetooth
®
version
Bluetooth
®
version 2.0
Radio interface
Bluetooth
®
Class1(1 to 100mW)
Installed profiles
ă
GAP : Generic Access Profile
ă
HSP : Headset Profile
ă
SPP : Serial Port Profile
ă
HFP : Hands Free Profile
Power consumption
About 0.8 W (excluding the telephone)
Power feeding method
Power feeding from the multifunctional telephone
Dimensions (L
×
W
×
H)
72mm
×
65mm
×
25mm
Mass
0.1kg
Operating environment
Temperature: 0 to 40
℃
, Relative humidity: 10 to 90% (no dew condensing)
Restrictions
Keep the IP3NA-BCH ADAPTER( ) at least 1m apart from other IP3NA-BCH adapters
and at least 3m apart from other radio equipment.
=2CKTKPI?
ĉĊ$CEM1-
Ĵ
Ĵ
ĵ
=$NWGVQQVJ*GCFUGV?
&GNGVG
%QPPGEV
ĉĊ$CEM1-
=&GNGVG?
&GNGVG$6&GXKEG1-!
$CEM1-
Ĵ
Ĵ
=$NWGVQQVJ?
2CKTKPI/QFG
8KUKDKNKV[
ĉĊ$CEM1-
Ĵ
ĵ
=8KUKDKNKV[?
&KUCDNG
'PCDNG
ĉĊ$CEM1-
Ĵ
ĵ
Ĵ
ĵ
=$NWGVQQVJ?
$6+PHQTOCVKQP
ĉĊ$CEM1-
Ķ
=$6+PHQTOCVKQP?
(KTOYCTG8GTUKQP::ZZ
*CTFYCTG8GTUKQP::ZZ
ĉĊ'ZKV
Ķ
Type of device
Available function
Remarks
Bluetooth
®
headset
・
Originating calls to an extension or central office line
Press the headset call (call control) key twice briefly and per-
form a dialing operation from the telephone.
・
Answering terminating calls
Press the headset call (call control) key while a call termi-
nates with a ring tone.
※
The headset call control key allows you to only originate
calls from the headset and answer terminating calls.
Any other headset-specific functions are not supported.
※
The handset cannot be used while you are talking with the
Bluetooth
®
headset on. You cannot switch to the Bluetooth
®
headset to use while you are using the handset, either.
・
The ringing of calls terminat-
ing to the headset is linked
with that of the telephone,
though some ringing fea-
tures, such as a busy tone,
are not supported.
※
For latest information about
recommended products,
browse the following Web
site:
http://www.necinfron-
tia.co.jp/
・
A headset with built-in Bluetooth
®
supporting the HFP/HSP profiles can be connected to the IP3NA-BCH
ADAPTER( ).
・
The receiver volume can be controlled with the multifunctional telephone (the cursor up and down
keys or the volume key).
・
Whether the functions mentioned above work or not depends on the destination system. For more
details, refer to the use’s guide that comes with the destination system.
・
The ways you originate calls from the Bluetooth
®
headset and answer terminating calls may vary
depending on the type of device you use.
A50-013691-001
Issue 1.0
2008.4
IP3NA-BHA ADAPTER Connection Manual
BHA-L UNIT
Bluetooth -ready
headset
R
Caution
