NEC DT920 User Manual Download

Page: 26 / 104

OUTLINE

LOWERING TILT LEGS

Turn the terminal over (key side down).

Lower Tilt Legs to desired height.

(1) Stopper
(2) Tilt Legs

Turn the terminal over (key side up).

CONNECTING LAN CABLE

ILPA-R UNIT is required when PoE
Hub supports NEC Proprietary
Protocol (The ILPA-R UNIT converts
IEEE802.3af to NEC Proprietary

Protocol). When ILPA-R UNIT is
used, 1000BASE-T is not available.

For details, please contact the
system administrator.

Connect LAN cable to the terminal following
steps.

Connect LAN cable to LAN cable connector
(LAN (=)) of the terminal.

Press the LAN cable into the groove.

(1) LAN Cable connector for PC (PC

Port)

(2) LAN Cable connector for the

premises

(3) LAN Cable

(4) Groove
(5) Terminal

When you connect the LAN cable to
a PC, connect the LAN cable to the

terminal's PC port and the PC.

ATTACHING DIRECTORY CARD

The Directory Card can be used to record often
dialed numbers or other important information.

Directory Card is optional.

Attach the Directory Card to the Directory Card
Holder.

Take the protective sheet off from the plastic
cover.

The surface of the plastic cover is put out.

Push the Directory Card Holder into the
grooves on the terminal until they snap into
place.

(1)  Plastic Cover
(2)  Directory Card
(3)  Directory Card Holder
(4)  Grooves

(1)

(2)

(1)

(2)

(3)

(4)

(5)

(1)

(2)

(3)

(4)

Summary of Contents for DT920









































































































Search results

Summary of Contents for DT920

Reviews:

Related manuals for DT920

Brands by name

Popular brands

NEC DT920, User Manual

Search results

Summary of Contents for DT920

Reviews:

Related manuals for DT920

Brands by name

Popular brands