manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 21 / 36

Share
Download
Neat INKA Technical Handbook Download Page 21

 

INKA, IOR, REPO & LINK 

3.1.3 Fixed Input 

 
If the ID code of the received radio message matches the 

fixed input

 ID code, then the corresponding 

actions configured for the fixed input will be performed. The fixed input ID code of an IOR, REPO or 
LINK unit is used when a transmitter wants to send specifically to this unit. It is not possible to change 
the fixed input ID code. 
 
 

3.1.4  Receive All Codes 

 
IOR, REPO and LINK can also be configured to accept all incoming radio messages, regardless of the 
ID code. If the unit is configured to accept all received radio messages, and the ID code of a received 
message does not match any of the ID codes in position 1-8, nor the fixed input ID code, then the 
actions configured for 

all codes

 will be performed. 

 

IOR 
REPO 
LINK 

Configure the unit to receive all radio 
messages regardless of the ID code 

Select “Yes” in list box 110. 

 

IOR 
REPO 
LINK 

Configure the unit to receive pre-
programmed ID codes only. 

Select “No” in list box 110. 

 
See section 2.2.4 for jumper configuration of which radio codes to receive. 
 
For each of the 8 radio positions and for the 

fixed input 

and for 

all codes

, the relay output activation 

and radio transmission can be configured individually.  
 
 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

21

 

Summary of Contents for INKA





































Reviews:

No comments