manualshive.com logo in svg

Neat INKA, Technical Handbook, Page: 16 / 36

Share
Download
Neat INKA Technical Handbook Download Page 16

 

INKA, IOR, REPO & LINK 

2.1.5  IOR Programmer, Preferences Tab 

 

 

315

314

313

312

311

301

323 

302

303

324 

304

316

305

306

333 

331 

332

307

308

334 

309

335 

 

Explanation of controls 

 
301 

Specifies power mode 

302 

Specifies whether a battery alarm shall be sent when the battery voltage is low 

303 

Specifies whether a mains failure alarm shall be sent when mains power is lost 

304 

Specifies whether a mains OK indication shall be sent when mains power returns 

305 

Test alarm interval (hours) 

306 

Battery charge duration (hours) 

307 

Out passage delay (s) 

308 

In passage delay (s) 

309 

Pulse activation time for relay (s) 

311 

Number of short packages in outgoing radio messages 

312 

Number of long packages in outgoing radio messages 

313 

Transmission delay (s) 

314 

Maximum number of hops 

315 

Same code inhibit time (s) 

316 

Disable acknowledge for incoming messages 

323 

Transmission delay according to jumper settings, field 313 is ignored 

324 

Maximum number of hops according to jumper settings, field 314 is ignored 

331 

Product type: INKA, IOR, REPO or LINK 

332 Firmware 

version 

333 

Hardware version (currently not used) 

334 Serial 

number 

335 Radio 

calibration 

 

Technical Handbook for the IOR Family (firmware v20.x), document number NE41 06007-02 v1.0 

16

 

Summary of Contents for INKA





































Reviews:

No comments