NDD easyone pro Operator'S Manual Download Page 99

Page: 99 / 188

EasyOne Pro™ / EasyOne Pro™ LAB

Switching the Device Off

Switching the Device Off

Caution

Loss of Data—Be sure to correctly terminate the program
before switching

EasyOne Pro™

off with the mains power

switch on the back.



Close the main valve of the gas cylinder.



Close the main valve of the O2 gas cylinder or disconnect the wall outlet.

Note

When using the wall outlet, please observe the hospital's in-
house instructions and requirements.



Quit the program with



Switch off

EasyOne Pro™

with

, or release gas pressure with

Release

pressure

, if you need to replace a gas cylinder. Then click

to confirm

the message.

EasyOne Pro™

will automatically switch off.

Caution

The device will switch off, but it remains connected to line
power. Only with the mains power switch at the back will

EasyOne Pro™

be disconnected from line power

Fig. 6-1

Summary of Contents for easyone pro





























































































































































































Search results

Summary of Contents for easyone pro

Reviews:

NDD easyone pro, Operator'S Manual, Page: 99 / 188

Search results

Summary of Contents for easyone pro

Reviews: