NAVIS A.467855.020 Reference Manual Download

Page: 130 / 228

NAVIOR-24S

™

Appendix B

Navis Standard Interface Protocol BINR

130

NAVIOR-24S ™

Revision

V1.00 20.05.2008

Time and frequency parameters

Request Packet 1Fh

Requesting a single transmission of time correlation parameters, packet- 1Fh doesn’t contain any
data and has following structure:

Note: Prior to transmission of time correlation parameters please set the time mark parameters in
packet D7h.
Requesting a repeated transmission (1-sec period) of time correlation parameters, packet 1Fh must
have following structure:

1 00 – disable packet transmission

01 – enable repeated transmission (1-sec period)
Data type format - INT8U

Summary of Contents for A.467855.020





































































































































































































































Search results

Summary of Contents for A.467855.020

Reviews:

Related manuals for A.467855.020

Brands by name

Popular brands

NAVIS A.467855.020, Reference Manual

Search results

Summary of Contents for A.467855.020

Reviews:

Related manuals for A.467855.020

Brands by name

Popular brands