NAVIS A.467855.020 Reference Manual Download

Page: 103 / 228

NAVIOR-24S

™

Appendix B

Navis Standard Interface Protocol BINR

103

NAVIOR-24S ™

Revision

V1.00 20.05.2008

Satellites using

Packet 12h. Allow/Forbid satellite using.

Packet 12h requests the data on the involved GPS/GLONASS-satellites and accepts or refuses use
of a satellite for the task processing.

1 - satellite system

Data type format – INT8U

2 - SV No

1–32 – for GPS
1 – 24 – for GLONASS
Data type format - INT8U

3 allow/forbid satellite using:

01 – to allow satellite using
02 – to forbid satellite using
Data type format - INT8U

Packet 12h in requesting mode contains no data and has following structure:

Summary of Contents for A.467855.020





































































































































































































































Search results

Summary of Contents for A.467855.020

Reviews:

Related manuals for A.467855.020

Brands by name

Popular brands

NAVIS A.467855.020, Reference Manual

Search results

Summary of Contents for A.467855.020

Reviews:

Related manuals for A.467855.020

Brands by name

Popular brands