Navim Group Company EsiWelma Sensigas UR.21.P Manual Download Page 1

 

EW146691_en - rev. A 

Gas Detectors 

 UR.21.P 

02/04/2020 

Gas detection systems for car parks and tunnels 

1/8

 

 

 

 

 

 

Sensigas

®

 

Gas Detectors 
for car parks and tunnels 

IP55 Protection Degree 

 

UR.21.P 

 

 

 

 

 

 

 

 

Sssssss 

10

…28Vdc power supply. 

Catalytic sensing element for flammable gases, and Electrochemical Cell for toxic gases. 
Up to three alarm threshold. 
Automatic counting life time of sensors.

 

Use 

The  UR.21.P  detectors,  being  specifically  designed  for  car  parks,  are  used  primarily  to  detect 
the presence of Gasoline Vapors and Carbon Monoxide (CO), but also Methane gas, LPG and, 
on demand, Nitrogen Monoxide (NO), Nitrogen Dioxide (NO

2

) and other gases. 

UR.21.P detectors can be used in stand-

alone mode with 4…20mA output and, in option, with a 

voltage-free  contact  relay  card,  or  variable  resistance  output  for  the  following  operational 
conditions: 

 

Pre-alarm, 1st alarm threshold, 2nd alarm threshold, Sensor Failure.

 

Operation 

In  case  of  a  gas  leak  the  detector  compares  the  measured  concentration  value  with  the 
intervention  thresholds  set  by  activating  the  relays  or  the  resistive  outputs  (if  provided) 
associated  with  them.  The  information  of  the  measured  concentration  value  is  always  present 
on the 4 ÷ 20mA output. 

Ordering

 

Simply indicate product code: please, refer to “available models”. 

Available models: 

 

 

 

 

 

 

 

 

 

Models on demand: 

 
 
 
 

 

 

Code:          UR xx yy z P

 

Sensing Element type: 
S = Standard; P= Professional. 
 

P= IP55 Protection Degree and design for car parks applications 

“21” for Stand Alone detectors with 4…20 mA output 
“41” for Bus Based System EW40 
 

G = Methane; P = LPG; O = Carbon Monoxide; B = Gasoline Vapours; 

 

N1 = Nitrogen Monoxide; N2 = Nitrogen Dioxide; 
L = Acetylene; I = Hydrogen; M = Ammonia (LIE); C = Propane; T = Octane; 
E = Ethyl Alcohol; X = Xylene; A = Acetone; H = Hexane; Q = Cycle-Hexane; 
T = Toluene; N = Pentane; U = Butane; F = Heptane; K = Ethane; V = Methanol; 
Z = Benzene; Y = Ethyl Acetate; HY = Hydrocarbons in general 

(1)

Summary of Contents for EsiWelma Sensigas UR.21.P









Reviews: