background image

 

V1.0 

 

 

OWNER’S MANUAL: Adjustable Height Wall Rack 

 

 

 

Keep this information for further reference. 

Thank you for purchasing a NavePoint product.   
 
Please examine the product for any damaged parts. If any part is damaged or missing, contact NavePoint for assistance. Do not attempt to install or 
use product if it has been damaged.  This product contains small items that could be a choking hazard – keep these items away from children. 

During installation, lay product contents on cardboard or other protective surface to avoid any damage. 

Do not use with equipment that is heavier than the indicated weight capacity for this product.  This product is designed to be installed indoors on 
wood stud walls, solid concrete walls or brick walls.   Make sure that the supporting surface will safely support the weight of the equipment and all 
attached hardware and components.  It is recommended that installation be performed by a qualified installer. NavePoint cannot be held 
responsible for damage to equipment or personal injury resulting from improper use or installation of product.  

Maintenance:  Check that the product is secure and safe to use at regular intervals (at least every three months). 

Limitations of Liability:  In no event will NavePoint, LLC. be liable for any damages, whether direct or indirect, special, punitive, incidental or 
consequential damages (including, but not limited to, lost profits or revenue, loss of use, lost business opportunities or loss of goodwill) or for the 
costs of procuring substitute products, arising out of or in connection with the use of the product, whether such liability arises from any claim 
based upon contract, warranty, tort (including negligence), product liability or otherwise, whether or not seller has been advised of the possibility 
of such loss or damage.  In no event will seller’s total cumulative liability, from all causes of action and all theories of liability, exceed the total 
amounts actually paid to seller by customer under the order that gives rise to any liability hereunder. 

Summary of Contents for 12U








Reviews: