manualshive.com logo in svg

Nautel NX5 AM, Preinstallation Manual

Share
Download
Nautel NX5 AM Preinstallation Manual Download Page 61

NX5 PRE-INSTALLATION MANUAL

PLANNING CONTROL/MONITOR CONNECTIONS

PAGE 1.8.2

VERSION 0.1  2015-08-01

Front Panel UI Control

The NX5’s front panel user-interface (UI) lets you locally control a number of transmitter functions and 
set parameters. For detailed information about the front panel UI, refer to the NX5 Operating and 
Maintenance Manual.

Remote Control

The remote AUI allows you to adjust any parameter and view any status available in the front panel UI 
via a web browser on a computer connected to the 

ETHERNET/LAN

 connector (J3A) on the control/

interface PWB (A4).

The transmitter also allows control and monitoring through an Ethernet connection via SNMP, 
supporting version 1 of the protocol, with traps.

The front panel UI or remote AUI also allow you to configure the remote inputs to control various 
transmitter functions and monitor the transmitter’s status by means of a conventional, parallel wire 
remote control interface (see 

“Remote Inputs” on page 1.8.3

 and 

“Remote Outputs” on page 1.8.8

) or an 

Ethernet connection (see 

“Web Based Control” on page 1.8.12

).

External System Interlock

An external safety interlock is available between pins 19 and 20 of the REMOTE I/O-A 25-pin male D-
sub connector (J6A) on the control/interface PWB (A4). This connection allows you to connect an 
external safety interlock circuit that provides an emergency RF inhibit control for the NX5. It must 
present a short circuit (low impedance) between the pins when the interlock circuit is intact and it is 
safe to enable the RF output. It must present an open circuit when any interlock switch is activated and 
the RF output requires inhibition. You can install any number of serial interlock switches.

External PDM Inhibit

An external PDM inhibit is available between pins 12 and 13 of the REMOTE I/O-A 25-pin male D-sub 
connector (J6A) on the control/interface PWB (A4). This connection allows you to configure an external 
PDM inhibit circuit that provides an emergency RF inhibit control for the NX5. It must present a short 
circuit (low impedance) between the pins when the PDM inhibit is active and the RF output requires 
inhibition. It must present an open circuit when it is safe to enable the RF output. 

Summary of Contents for NX5 AM


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands