natus ErgoJust LTM Instructions For Use Manual Download

Page: 40 / 86

Natus ErgoJust LTM and ErgoJust ICU Cart Instructions For Use

3-10

July 6, 2020

Mounting the cart video pole -

Natus ErgoJust LTM and ErgoJust ICU

It is recommended to use an assistant when mounting the video pole to avoid injury or

damage to the equipment.

1. Position the Video

Pole brackets

NOTE:

Steps 1 - 4 are required only if the Video Pole mounting screws were removed instead of

loosened when the Video Pole was removed.

Improper positioning of the two mounting brackets will allow the Video Pole to

separate from the bottom mast, which may damage system components or cause an injury.

1. Place one of the brackets inside the video pole with the indented side positioned against the

video pole as shown in Figure 1.

Figure 1: Proper orientation of the mounting brackets inside the Video Pole.

Legend Description

Indented side facing outward

Video pole

Summary of Contents for ErgoJust LTM























































































Search results

Summary of Contents for ErgoJust LTM

Reviews:

Related manuals for ErgoJust LTM

Brands by name

Popular brands

natus ErgoJust LTM, Instructions For Use Manual

Search results

Summary of Contents for ErgoJust LTM

Reviews:

Related manuals for ErgoJust LTM

Brands by name

Popular brands